Ford Viscosity Flow Cup Ford Viscosity Cup Cup Sizes Available 1#2#3#4#5#

Description: Ford Viscosity Flow Cup Ford Viscosity Cup Cup Sizes Available 1#2#3#4#5# Instruction manual Ford cup according to the American Society for Testing and Materials paint and raw materials standards ASTM D 1200, D333, D365 in the production, used to determine the viscosity of inks, paints, lacquers and other viscosity more convenient viscometer. It is made of high quality aluminum cup with a small hole at the bottom and a capacity of about 100ml. Ford cup by determining the aluminum cup in a certain capacity of the test material from the bottom of the small hole in the time required to flow out to measure the viscosity of the test material. I. Technical parameters 1, cup volume: 100 ± 1ml 2, a variety of cup indicators Cup numberHole diameterMeasuring rangeOutflow time1#2.10 mm10-35 cSt25-105 sec2#2.80 mm25-120 cSt25-105 sec3#3.40 mm49-220 cSt25-105 sec4#4.10 mm70-370 cSt20-105 sec5#5.20 mm200-1200 cSt20-105 sec II. Equipment and appliances: 1. Stopwatch: accuracy 0.1 (optional)2. Ford cup holder (optional) III. Usage: 1, should be selected before the use of suitable solvents will be wiped clean inside the wall of the cup (Note: Please pay special attention to the cleaning of small holes in the cup, can be twisted into a rope of soft paper, in the outflow holes in the repeated pull); and then dry in the air or with a cold wind blowing dry, do not allow the past measurement of the liquid residue adhering to the liquid in the cup or flow outlet. 2, the selection of appropriate cup number, in order to control the outflow time between 20 to 80 seconds (see technical parameters) 3, the test solution is stirred and filtered in not less than 567 holes / cm2 of the sieve, and make the sample and outflow cup temperature adjustment to (23 ± 0.5 ℃) or another agreed temperature 4、Adjust the Ford Cup holder to center the horizontal bubble above. 5, the sample will be injected into the Ford Cup, at the same time with a finger to plug the outflow hole (if corrosive liquids available baffle plug the outflow hole), filled with a metal or glass plate in the cup to scrape the flat, will be excess specimen scraped into the edge of the viscosity cup grooves, placed to take over the cup. 6, will release the finger or push away from the baffle, the specimen flow out vertically, and at the same time open the stopwatch. When the first breakpoint to stop the clock, the seconds of outflow time is the viscosity value of the sample to be measured. 7, repeat the measurement three times, take the average value for the final reading. 8, immediately with a suitable solvent for its cleaning. Never use metal cleaning tools or wire. If the outflow hole is stained by dry sediment, the application of suitable solvents to make it soft, and then carefully cleaned, such as with a soft cloth through the outflow hole rubbing cleaning. IV. Maintenance Precautions Because of the Ford Cup falls, collision will make the small hole part of the damage or deformation, measurement error, in use to be very caring. V. Calibration Calibration 1, the instrument should be calibrated regularly after each year of use (factory nozzle diameter in the factory with traceable to the NIST oil has been calibrated with Newtonian oil, the user does not need to be calibrated within one year after purchase) 2, calibration needs to use standard silicone oil in accordance with the relevant national viscosity cup measurement procedures. VI. Other For a particular dip cup to get the results at a specified temperature in “seconds” to express. Convert “seconds” to centistokes, see ASTM D 4212. Cup numberApplicationskc2Thin oils, mixed coatings, varnishes1.247703Medium viscosity, mixed coatings, varnishes2.315504Thicker fluids and mixtures3.7400

Price: 80 USD

Location: 合肥

End Time: 2025-02-15T03:00:22.000Z

Shipping Cost: 0 USD